The equipment adopts intelligent control system. In the automatic mode, the status of the mold in the chamber will be judged each time it is started, and the running order will be adjusted intelligentiously. Even when the power is turned off, the system can remember the current state of the molding mold, so as to avoid the direct restart when the power is cut off. The manual mode input mold is not identified temporarily, and its mold number is not displayed on the touch screen; In automatic mode operation, when the cylinder action is abnormal, the system automatically enters the suspended state, and there is an alarm, after the fault recovery, press the start key to continue working, in the current mode can not be processed can be converted to manual mode, after the fault recovery, and then turn back to the automatic mode to start.
NO | 項目區分 | 內容 | 詳細規格 |
1 | 基本參數 | 動力源 | 電源:三380VAC/82KVA(選配) 啟動功率:75KW; 運行功率:22~31KW |
壓縮空氣:0.55MPa±5%;75升/min; 冷卻水:0.3MPa,40~60升/min;20±1℃ 氮氣:0.3MPa±5%(純度99.999%);40~60升/min,含氧量≤2ppm | |||
模具規格 | 方型:最大180mm×120mm 上下模具(含預型玻璃)總高度允許高度范圍:26mm~70mm | ||
最高工作溫度 | 750°、850°C(選配)升溫時間 15-20Min以下 | ||
外形尺寸、重量 | 2960(L)×1310(W)×2110(H);重量約:2120kg | ||
2 | 壓力頭構成 | 預熱1、2、3、4 | 通過加熱裝置控制模具和玻璃的快速、均勻加熱。 |
成型1、2 | 利用精密電氣比例閥控制下降方式。分辨率0.001 MPa,可以根據工藝要求精確調節壓力 | ||
冷卻1、2 | |||
冷卻3 | 利用精密調壓閥控制下降方式。為了保護模具及已成型的玻璃的品質,緩慢下降模具和玻璃的溫度。 | ||
3 | 冷卻4 | 利用自重下降方式。為了保護模具及已成型的玻璃,防止模具在外部露出時產生氧化,并且加快其冷卻效果。 | |
4 | 外部冷卻/輔助冷卻 | 利用自重下降方式。為了保護模具及已成型的玻璃,同時為作業者取拿前做充分冷卻。 | |
5 | 模具移送 | 移送 | 利用氣缸和高精度電缸進行模具的移送 |
6 | 環境要求 | 潔凈度 | 10000級以下(推薦1000級以下、或在操作平臺上放置百級FFU以保證局部潔凈度) |
環境濕度 | 30-60%,但不可有結露 | ||
環境溫度 | 22℃±3℃,但不可有結露 | ||
7 | 均熱板規格 | 上均熱板尺寸 | 200mm(L)×125mm(W)×10(H) |
下均熱板尺寸 | 200mm(L)×138mm(W)×10(H) | ||
均熱板平面度 | ≤5um | ||
均熱板材質 | 合金板 |